Furnace Repair in Yakima, WA
Most furnace failures come down to a handful of parts: igniters, flame sensors, pressure switches, blower motors and control boards. We carry the common ones so a lot of calls finish in one visit.
If you have been searching for furnace repair near me in Yakima, this is the page. We cover Yakima and the wider Yakima Valley, and the number below reaches a real person at any hour of the day.
Signs you need furnace repair in Yakima
- Furnace ignites then shuts down after a few seconds
- Blower runs constantly but the burners never fire
- Short cycling on and off without reaching temperature
- Yellow or lazy burner flame instead of steady blue
- Clicking with no ignition at the burner
- Rattling sheet metal or a squealing blower wheel
- Carbon monoxide alarm sounding near the furnace
- Furnace tripping its own limit and locking out
Need furnace repair help in Yakima today?
(888) 380-4427Answered by a person 24 hours a day, 7 days a week. Tell us what the system is doing and we will give you an arrival window before you hang up.
What our Furnace Repair service in Yakima includes
- Hot surface igniter and flame sensor cleaning or replacement
- Gas valve, burner and manifold pressure service
- Inducer motor and pressure switch repair
- Blower motor, wheel, belt and capacitor replacement
- Circuit board, transformer and wiring repair
- Heat exchanger inspection and combustion analysis
- Flue, venting and draft correction
- Safety lockout diagnosis and reset
How we price it
We charge a diagnostic fee to come out and find the actual fault. Once we know what failed, you get a fixed price for the repair and you decide before we touch anything. Nights and weekends cost the same as weekdays.
Turnaround
Most furnace repair jobs in Yakima are finished on the first visit because the common parts ride on the truck. Anything that needs ordering gets a firm timeline.
Serving Yakima and the surrounding area
What Washington homeowners say
“I had two other companies tell me I needed a whole new system. These guys found a bad control board, replaced it, and the unit has run fine ever since.”
Anthony P. — verified customer“Booked a tune-up before summer. The tech spent almost two hours, cleaned the coil, and gave me a written list of what to keep an eye on. No pressure to buy anything.”
Karen S. — verified customer“Heat pump was icing over and blowing cold. Turned out to be the defrost board. Fixed the same day and explained exactly what went wrong.”
Diego M. — verified customerFurnace Repair in Yakima: common questions
Do you carry the parts, or is it a second trip?
Trucks working Yakima carry the parts that fail most often, so the majority of repairs finish on the first visit. If a part has to be ordered, we tell you the timeline up front.
Is there an extra charge for evenings or weekends in Yakima?
No. Nights, weekends and holidays are billed at the same posted rates as a weekday.
Do you cover the areas around Yakima?
Yes. We work throughout Yakima and the wider Yakima Valley, including Parker, Selah and Sunnyside and the rest of Washington.
What brands do you work on?
All major residential brands, including Carrier, Trane, Lennox, Rheem, Goodman, Bryant, American Standard, York, Amana, Daikin and Mitsubishi. Repair does not depend on the badge on the cabinet.
My furnace clicks but never lights. What is that?
Most often a cracked hot surface igniter or a dirty flame sensor, both inexpensive and both stocked on the truck. It can also be a pressure switch or gas valve fault.
What is furnace short cycling and is it dangerous?
It is the furnace shutting down before it satisfies the thermostat, usually from a dirty filter, a failing flame sensor or an overheating limit. It wears the equipment out early and should be looked at.
Related guides
Need furnace repair help in Yakima today?
(888) 380-4427Answered by a person 24 hours a day, 7 days a week. Tell us what the system is doing and we will give you an arrival window before you hang up.